P.S.GoShikenがGoogle Driveで共有している無料の2024 Juniper JN0-351ダンプ:https://drive.google.com/open?id=17jEhqpSvd03xIFrVcczwyE4cbsp7Tgp3
私たちJuniperのJN0-351学習クイズは、仕上げの体系的な分析の分野での近年の試験状況のさまざまな専門家から作られ、学生の要求をできるだけ満たし、同時にチェックとレビューを行う専門スタッフがいますJN0-351実践教材、学生の学習に高品質の情報を楽しんでもらいました。 試験の多様性により、GoShikenのJN0-351学習教材もさまざまな種類の学習教材にまとめられているため、学生は必要なJN0-351ガイド急流の情報をすばやく見つけることができます。
トピック | 出題範囲 |
---|---|
トピック 1 |
|
トピック 2 |
|
トピック 3 |
|
トピック 4 |
|
トピック 5 |
|
トピック 6 |
|
JN0-351認定試験は現在で本当に人気がある試験ですね。まだこの試験の認定資格を取っていないあなたも試験を受ける予定があるのでしょうか。確かに、これは困難な試験です。しかし、難しいといっても、高い点数を取って楽に試験に合格できないというわけではないです。では、まだ試験に合格するショートカットがわからないあなたは、受験のテクニックを知りたいですか。今教えてあげますよ。それはGoShikenのJN0-351問題集を利用することです。
質問 # 58
You are a network operator who wants to add a second ISP connection and remove the default route to the existing ISP You decide to deploy the BGP protocol in the network.
What two statements are correct in this scenario? (Choose two.)
正解:A、C
解説:
A is correct because IBGP updates the next-hop attribute to ensure reachability within an AS. This is because the next-hop attribute is the IP address of the router that advertises the route to a BGP peer. If the next-hop attribute is not changed by IBGP, it would be the IP address of an external router, which may not be reachable by all routers within the AS. Therefore, IBGP updates the next-hop attribute to the IP address of the router that received the route from an EBGP peer1.
B is correct because IBGP peers advertise routes received from EBGP peers to other IBGP peers. This is because BGP follows the rule of advertising only the best route to a destination, and EBGP routes have a higher preference than IBGP routes. Therefore, IBGP peers advertise routes learned from an EBGP peer to all BGP peers, including both EBGP and IBGP peers1.
質問 # 59
You are asked to connect an IP phone and a user computer using the same interface on an EX Series switch.
The traffic from the computer does not use a VLAN tag, whereas the traffic from the IP phone uses a VLAN tag.
Which feature enables the interface to receive both types of traffic?
正解:D
解説:
Explanation
The feature that enables an interface on an EX Series switch to receive both untagged traffic (from the computer) and tagged traffic (from the IP phone) is the voice VLAN12.
The voice VLAN feature in EX-series switches enables access ports to accept both data (untagged) and voice (tagged) traffic and separate that traffic into different VLANs12. This allows the switch to differentiate between voice and data traffic, ensuring that voice traffic can be treated with a higher priority12. Therefore, option D is correct.
質問 # 60
Which two statements are correct about tunnels? (Choose two.)
正解:A、C
解説:
Explanation
A tunnel is a connection between two computer networks, in which data is sent from one network to another through an encrypted link. Tunnels are commonly used to secure data communications between two networks or to connect two networks that use different protocols.
Option B is correct, because tunnel endpoints must have a valid route to the remote tunnel endpoint. A tunnel endpoint is the device that initiates or terminates a tunnel connection. For a tunnel to be established, both endpoints must be able to reach each other over the underlying network. This means that they must have a valid route to the IP address of the remote endpoint1.
Option D is correct, because tunnels add additional overhead to packet size. Tunnels work by encapsulating packets: wrapping packets inside of other packets. This means that the original packet becomes the payload of the surrounding packet, and the surrounding packet has its own header and trailer. The header and trailer of the surrounding packet add extra bytes to the packet size, which is called overhead. Overhead can reduce the efficiency and performance of a network, as it consumes more bandwidth and processing power2.
Option A is incorrect, because BFD can be used to monitor tunnels. BFD is a protocol that can be used to quickly detect failures in the forwarding path between two adjacent routers or switches. BFD can be integrated with various routing protocols and link aggregation protocols to provide faster convergence and fault recovery.
BFD can also be used to monitor the connectivity of tunnels, such as GRE, IPsec, or MPLS.
Option C is incorrect, because IP-IP tunnels are stateless. IP-IP tunnels are a type of tunnels that use IP as both the encapsulating and encapsulated protocol. IP-IP tunnels are simple and easy to configure, but they do not provide any security or authentication features. IP-IP tunnels are stateless, which means that they do not keep track of the state or status of the tunnel connection. Stateless tunnels do not require any signaling or negotiation between the endpoints, but they also do not provide any error detection or recovery mechanisms.
References:
1: What is Tunneling? | Tunneling in Networking 2: What Is Tunnel In Networking, Its Types, And Its Benefits? : [Configuring Bidirectional Forwarding Detection] : [IP-IP Tunneling]
質問 # 61
You are troubleshooting a BGP routing issue between your network and a customer router and are reviewing the BGP routing policies. Which two statements are correct in this scenario? (Choose two.)
正解:B、C
解説:
Explanation
In BGP, routing policies are used to control the flow of routing information between BGP peers1.
Option C suggests that import policies are applied after the RIB-In table. This is correct because import policies in BGP are applied to routes that are received from a BGP peer, before they are installed in the local BGP Routing Information Base (RIB-In)1. The RIB-In is a database that stores all the routes that are received from all peers1.
Option D suggests that export policies are applied after the RIB-Local table. This is correct because export policies in BGP are applied to routes that are being advertised to a BGP peer, after they have been selected from the local BGP Routing Information Base (RIB-Local)1. The RIB-Local is a database that stores all the routes that the local router is using1.
Therefore, options C and D are correct.
質問 # 62
What is the default keepalive time for BGP?
正解:B
解説:
Explanation
The default keepalive time for BGP is 60 seconds1. The keepalive time is the interval at which BGP sends keepalive messages to maintain the connection with its peer1. If the keepalive message is not received within the hold time, the connection is considered lost1. By default, the hold time is three times the keepalive time, which is 180 seconds1.
質問 # 63
......
GoShikenは、試験に最適な試験JN0-351試験ガイドを提供します。 JN0-351練習トレントの有効性と信頼性は、専門家によって確認されています。多くのお客様が当社のヘルプでJN0-351試験に合格しています。 JN0-351テスト資料はホームページで更新され、JN0-351認定試験に関連する情報をタイムリーに更新します。最も有効で費用対効果の高いJN0-351準備資料を入手できるように、pdf塾でプロモーションを行います。そのため、JN0-351トレーニングガイドを安心してお選びいただけます。
JN0-351受験対策解説集: https://www.goshiken.com/Juniper/JN0-351-mondaishu.html
P.S.GoShikenがGoogle Driveで共有している無料の2024 Juniper JN0-351ダンプ:https://drive.google.com/open?id=17jEhqpSvd03xIFrVcczwyE4cbsp7Tgp3
S'il vous plait Connectez-vous ou Créér un compte pour repondre.